Gnatenko I.A., Zabolotnyj S.D. Lisovenko A.A., Lukash V.A, Tsap I.V., Prisjazhnjuk P.N. Welding with friction with mixing aluminum alloys V95

  • И. А. Гнатенко
  • С. Д. Заболотный
  • А. А. Лисовенко
  • В. А. Лукаш
  • И. В. Цап
  • П. Н. Присяжнюк
Keywords: friction stir welding, aluminum alloy, structure, grain size of the alloy

Abstract

The possibility of welding an aluminum alloy V95 considered, the microstructure of the welded joint investigated, the main zones are determined, and the phase composition investigated. When welded by friction with stirring of an aluminum alloy, three zones are revealed in its structure. It is established that when welding by this method, the grain size of the alloy decreases by a factor of 10 (from 50 μm to 5 μm).

References

1. Fridljander I.N., Senatorova O.G., Tkachenko E.A., Molostova I.I. Razvitie i primenenie vysokoprochnyh splavov sistemy Al–Zn–Mg–Cu dlja aviakosmicheskoj tehniki // V sb. «75 let. Aviaci-onnye materialy. Izbrannye trudy «VIAM» 1932–2007»: Jubilejn. nauch.-tehn. sb. / Pod obshh. red. E.N. Kablova. – M.: VIAM. 2007. – S. 157–163.
2. Osincev O.E., Konkevich V.Ju. Vysokoprochnye bystrozakristalli-zovannye aljuminievye splavy sistem Al–Zn–Mg i Al–Zn–Mg–Cu // Tehnologija legkih splavov. – 2010. – № 1. – S. 157–163.
3. Ngo Than' Bin', N.A. Dzhindo, A.B. Semenov, B.I. Semenov TIKSOFORMING VYSOKOPROChNYH SPLAVOV SISTEMY Al—Zn—Mg—Cu Vestnik MGTU im. N.Je. Baumana. Ser. “Mashinostroenie”. 2012
4. V.M. Beleckij, G.A. Krivov. Aljuminievye splavy (sostav, svojstva, tehnologija, primene-nie) spravochnik / Pod obshhej redakciej akademika RAN I.N. Fridljandera. K.: Kominteh, (2005), 315s.
5. D.E. Pedun, V.P. Pojda, V.V. Brjuhoveckij, A.V. Pojda, T.F. Suhova, A.L. Samsonik, V.V. Lit-vinenko, E.A. Spiridonov. Vysokotemperaturnaja strukturnaja sverhplastichnost' i chastichnoe plavle-nie vysokoprochnogo splava 1933 sistemy Al-Mg-Zn-Cu-Zr. Vіsnik HNU, № 1019, serіja «Fіzika», vip. 16, 2012
6. Sverhplasticheskaja formovka konstrukcionnyh splavov / Pod red. N. Pejtona, K. Gamil'to-na: Per. s ang. M.: Metallurgija, (1985), 218s.
7. Materialovedenie: Uchebnik dlja vysshih tehnicheskih uchebnyh zavedenij. B.N. Arzamasov, I.I. Sidorin, G.F. Kosolapov i dr.; Pod obshh. Red. B.N. Arzamasova. – 2-e izd., ispr. I dop. – M.: Mashi-nostroenie, 1986. – 384 s.
8. Metallovedenie i termicheskaja obrabotka metallov/ Ju.M. Lahtin. Izd. 3 –e pererab. I dop. – M., «Metallurgija», 1983.
9. Modelirovanie teplovyh processov dlja uluchshenija struktury metallov i splavov metodom trenija s peremeshivaniem /A.L. Majstrenko, V.M. Nesterenkov, V.A. Dutka, V.A. Lukash, S.D. Zabolot-nyj1, V.N. Tkach//Avtomaticheskaja svarka, № 1. – 2015. – S.5–14
10. Friction stir welding of aluminium alloys / P.L. Threadgill, A.J. Leonard, H.R. Shercliff , P.J. Withers // Int. Mater. Rev. – 2009. – 54, № 2. – P. 49–93.
11. Vosstanovlenie plit mednyh kristallizatorov nepreryvnoj razlivki stali metodom naplavki treniem s peremeshivaniem / V.I. Zelenin, M.A. Poleshhuk, E.V. Zelenin i dr. // Porodorazru-shajushhij i metalloobrabatyvajushhij instrument – tehnika i tehnologija ego izgotovlenija i primene-nija. – 2010. – Vyp. 13. – S. 476–479.
12. Instrumenty dlja stykovyh, nahlestochnyh, tavrovyh svarochnyh soedinenij, naplavki i klepki treniem s peremeshivaniem. // Nauchno-tehnicheskij zhurnal «Tehnologicheskie sistemy» 1(78)2017 s. 97
13. Srinivasa Rao G., Subba Rao V. V., Kotesvara Rao S.R. Mikrostruktura i korrozija v sole-vom tumane svarennogo treniem s peremeshivaniem aljuminievogo splava AA2219/ Metallofizika i no-vejshie tehnologii, tom 37, vypusk 4.
Published
2018-07-04
How to Cite
Гнатенко, И., Заболотный, С., Лисовенко, А., Лукаш, В., Цап, И., & Присяжнюк, П. (2018). Gnatenko I.A., Zabolotnyj S.D. Lisovenko A.A., Lukash V.A, Tsap I.V., Prisjazhnjuk P.N. Welding with friction with mixing aluminum alloys V95. Problems of Tribology, 87(1), 106-110. Retrieved from http://tribology.khnu.km.ua/index.php/ProbTrib/article/view/661
Section
Articles