The influence of alloying with manganese and chromium of steel hardened and tempered auger on its relative wear resistance during dehydration in a municipal solid waste truck

Authors

  • O.V. Bereziuk Vinnitsa National Technical University
  • V.I. Savulyak Vinnitsa National Technical University
  • V.O. Kharzhevskyi Khmelnitskyi National University

DOI:

https://doi.org/10.31891/2079-1372-2022-106-4-51-57

Keywords:

wear, wear resistance, manganese content, chromium content, tempering, auger press, garbage truck, dehydration, municipal solid waste, regression analysis

Abstract

The article is dedicated to the study of the influence of alloying with manganese and chromium followed by hardening and tempering of the auger on its wear resistance during the dehydration of municipal solid waste truck. The use of a mathematical apparatus and appropriate regression analysis programs made it possible to determine the dependence of the wear resistance of the auger on the content of manganese and chromium in the steel of the auger for the case of its quenching and tempering. Constructed graphical dependences of relative wear resistance with the indicated alloying and heat treatment of the screw revealed a significant influence of the concentration of manganese and chromium in steel, sufficient convergence of the obtained patterns was confirmed. It was established that after operation and wear on the path s = 56850 m during the dehydration of solid waste in a garbage truck, an increase in the manganese content in the steel of the heat-treated screw from 0.32% to 1.8% leads to a decrease in energy intensity by 10 kWh/tons, and an increase chromium content in screw steel after similar heat treatment from 0% to 6% leads to a decrease in energy consumption by 11.5 kWh/tons and to a reduction in the cost of the solid waste dehydration process in the garbage truck. It was determined that tempering the chromium-manganese screw steel after its hardening allows reducing energy consumption by 1.26...2.56 kWh/tons, depending on the chromium content. The expediency of conducting further research on determining the rational composition and structural state of the auger material and ways to increase its wear resistance has been revealed

References

Kutsova V.Z., Kindrachuk M.V., Kovzel M.A., Tisov O.V., Grebeneva A.V., Shvets P.Yu. (2016) Vplyv struktury, fazovogo skladu ta vlastyvostej na abrazyvnu znosostijkist' hromomargancevyh chavuniv u lytomu stani [The impact of the structure, phase structure and power on the abrasive wear resistance of chromium-manganese chavuns at the cast steel]. Problem of Friction and Wear, 2, 78-85.

Dykha O.V.(2018) Rozrahunkovo-eksperymental'ni metody keruvannja procesamy granychnogo zmashhuvannja tehnichnyh trybosystem [Computational and experimental methods of controlling processes of boundary lubrication of technical tribosystems]: monograph. Khmelnytskyi: KhNU.

Vlasyuk I.A., Mogylatenko V.G., Yamshinskyi M.M., Tovkach A.M. (2011). Vplyv lehuvalnykh elementiv na strukturu i vlastyvosti znosostiikykh stalei [The influence of alloying elements on the structure and properties of wear-resistant steels]. Metal and casting of Ukraine, 1, 26-28.

Malinov V.L. (2011) Vlijanie soderzhanija marganca i rezhimov otpuska na strukturu i iznosostojkost hromomargancevogo naplavlennogo metalla [The influence of manganese content and tempering regimes on the structure and wear resistance of chrome-manganese deposited metal]. Protection of metallurgical machines from breakdowns: coll. of scientific papers, 13, 247-254.

Tsymbal B.M.(2017) Pidvyshhennja znosostijkosti shnekovyh ekstruderiv dlja vyrobnyctva palyvnyh bryketiv u kyslotnyh ta luzhnyh seredovyshhah [Increasing the wear resistance of screw extruders for the production of fuel briquettes in acidic and alkaline environments]: abstract dis. … cand. tech. sciences: 05.02.04 – Friction and wear in machines, Kharkiv, 20.

Hevko R.B., Zalutskyi S.Z., Hladyo Y.B., Tkachenko I.G., Lyashuk O.L., Pavlova O.M., ... & Dobizha N.V. (2019). Determination of interaction parameters and grain material flow motion on screw conveyor elastic section surface. INMATEH-Agricultural Engineering, 57(1).

Goldshtein M.I., Grachev S.V., Veksler Y.G. (1999) Special'nye stali [Special steels]. M.: MISIS.

Orisaleye J.I., Ojolo S.J., Ajiboye J.S. (2019) Pressure build-up and wear analysis of tapered screw extruder biomass briquetting machines. Agricultural Engineering International: CIGR Journal, 21(1), 122-133.

Dvoruk V.I. (2014) Vplyv lehuvannia khromom konstruktsiinoi stali na yii abrazyvnu znosostiikist pislia vysokotemperaturnoi termomekhanichnoi obrobky [Effect of chromium alloying of structural steel on its abrasive wear resistance after high-temperature thermomechanical treatment]. Problems of Tribology, 3, 59-65.

Demirci A., Teke I., Polychronopoulos N. D., Vlachopoulos J. (2021) The Role of Calender Gap in Barrel and Screw Wear in Counterrotating Twin Screw Extruders. Polymers, 13(7), 990.

Tataryants M.S., Zavinsky S.I., Troshin A.G. (2015) Razrabotka metodiki raschjota nagruzok na shnek i jenergozatrat shnekovyh pressov [Development of a method for calculating the loads on the auger and the energy consumption of screw presses]. ScienceRise, 6(2), 80-84

Bereziuk O.V. (2018) Eksperymental"ne doslidzhennya procesiv znevodnennya tverdyx pobutovyx vidxodiv shnekovym presom [Experimental study of the processes of dehydration of solid household waste with a auger press]. Bulletin of the Vinnitsa Polytechnic Institute, 5, 18-24.

Bereziuk O.V., Savulyak V.I., Kharzhevskyi V.O. (2021) The influence of auger wear on the parameters of the dehydration process of solid waste in the garbage truck. Problems of Tribology, 26(2/100), 79 86.

Bereziuk O.V., Savulyak V.I., Kharzhevskyi V.O. (2022) The influence of the alloying of the auger by the chromium on its wear during dehydration process of municipal solid waste in the garbage truck. Problems of Tribology, 27(1/103), 50-57.

Chatterjee S., Hadi A.S. (2015) Regression analysis by example. John Wiley & Sons.

Downloads

Published

2022-12-18

How to Cite

Bereziuk, O., Savulyak, V., & Kharzhevskyi, V. (2022). The influence of alloying with manganese and chromium of steel hardened and tempered auger on its relative wear resistance during dehydration in a municipal solid waste truck. Problems of Tribology, 27(4/106), 51–57. https://doi.org/10.31891/2079-1372-2022-106-4-51-57

Issue

Section

Articles

Most read articles by the same author(s)

1 2 > >>