Osipov M.Y. Research of the effect of alloys structural condition on their resistance to abrasive wear under elevated temperatures

Authors

  • М.Ю. Осипов

Abstract

The paper reflects the results of alloys structural condition effect in terms of field tests under abrasive wear and ele-vated (up to 500 - 550 °C) temperatures. The tests were performed on mixer scrapers which mix refractory mass for pressing chamotte refractories. Scraper edges were subjected to intense abrasive wear and heated up to 550 °C at the result of friction with the skin of compressed re-fractory mass. Scraper plates installed at the same place and periodically replaced served as samples. The plates were made of high-speed steel Х12Ф1 and Х12 and then heat-treated to different structural conditions of matrix alloys containing vari-ous amounts of carbide phase. It was found that under conditions of abrasive wear and temperatures up to 550 °C the lowest wear resistance have the materials with ferritic matrix, while the highest wear resistance have predominantly materials with martensitic condition. Austenitic-martensitic alloys occupy intermediate position in wear resistance scale. It was established that carbide phase plays the most important role in wear resistance improving under such condi-tions. The test results demonstrate the existence of proportional relation between wear resistance and hardness, while under one type of matrix, - between the wear resistance and the amount of carbide phase.

References

1. Geller Ju.A. Instrumental'nye stali. M.: Metallurgija, 1983, 527 p.
2. Rauzin Ja.R. Termicheskaja obrabotka hromistoj stali. M.: Mashinostroenie, 1978, 277 p.
3. Porada I.L., Vorob'ev G.M., Vasilenko G.I., Natapov B.S. O pereraspredelenii legirujushhih jelemen-tov mezhdu tverdym rastvorom i karbidnoj fazoj v processe otpuska zakalennoj stali tipa ШХ15СГМФШ. Izv. VUZov. Chernaja metallurgija, 1974, №8, pp. 96-98.
4. Polishhuk I.E., Braun M.P. Vlijanie karbidnoj fazy na iznosostojkost' lityh hromistyh slozhnolegiro-vannyh stalej. K., 1972, pp. 169-173.
5. Larsen-Basse J., Shtishido С.М., Tanouye P.A. Journal Austral. Inst. Metals. 1974, v. 19, рp. 270-275.
6. Gat N., Tabakoff N. Some effects of temperature on the erosion of metals. Wear, 1978, v. 50, №1, рp.85-94.
7. Vosstanovlenie i povyshenie iznosostojkosti i sroka sluzhby detalej mashin. Pod red. V.S. Popova. Zaporozh'e, izd-vo OAO "Motor Sich", 2000, 394 p.
8. Grinberg N.A., Livshic L.S., Shherbakov V.S. O vlijanii legirovanija ferrita i karbidnoj fazy na iznosostojkost' stalej. Metallovedenie i term. obrab. metallov, 1971, №9, pp. 57-59.
9. Tylkin M.A. Povyshenie dolgovechnosti detalej metallurgicheskogo oborudovanija. M.: Metallurgija, 1971, 608 p.
10. Popov V.S., Brykov N.N., Dmitrichenko N.S., Pristupa P.G. Dolgovechnost' oborudovanija ogne-upornogo proizvodstva. M.: Metallurgija, 1978, 232 p.
11. Popov V.S., Brykov N.N., Pugachev G.A. Povyshenie iznosostojkosti splavov so strukturoj me-tastabil'nogo austenita pri abrazivnom iznashivanii. Fiz.-him. mehanika materialov, 1979, t. 15, №5, pp. 97-100.
12. Brykov N.N., Pugachev G.A., Brykov M.N. Vlijanie uslovij iznashivanija na stepen' uprochnenija i iznosostojkost' metastabil'nyh austenitnyh splavov. Problemy trybologіi (Problems of tribology). Khmel'nyts'kyi, KhNU, 2003, No3-4, pp.158-173.
13. Filippov M.A., Litvinov V.S., Nemirovskij Ju.R. Stali s metastabil'nym austenitom. M.: Metallur-gija, 1988, 256 p.
14. Malinov L.S. Stali i chuguny s metastabil'nym austenitom i jeffektom samozakalki pri nagruzhenii - raznovidnost' adaptacionnyh materialov, povyshajushhih svoi svojstva pri vneshnem vozdejstvii za schet samoorganizacii struktury. Metall i lit'e Ukrainy, 2003, №11-12, pp. 3-9.
15. Chejljah A.P. Vozmozhnosti sozdanija metastabil'nyh sostojanij austenita v splavah na osnove zheleza. Novi materialy i tehnologii v metalurgii ta mashynobuduvanni. 2002, №2, pp. 31-34.
16. Issledovanie uslovij jekspluatacii i haraktera iznashivanija skrebkov smesitelej. Popov V.S. i dr. Ogneupory: Nauchno-proizvodstvennyj zhurnal, M.: 1988, №8, pp.38-40.
17. Guljaev A.P. Metallovedenie. M.: Metallurgija, 1977, 647 p.
18. Popov V.S., Brykov N.N., Dmitrichenko N.S. Iznosostojkost' press-form ogneupornogo proizvod-stva. M.: Metallurgija, 1971, 160 p.
19. Gudremon Je. Special'nye stali. M.: Metallurgija, 1966, t. 1, 736 p., t. 2, 1274 p.
20. Bannyh O.A., Kovalenko O.I. Fazovye prevrashhenija i izmenenie struktury pri nagreve hromomar-gancovomolibdenovoj austenitno-martensitnoj stali. Izv. AN SSSR. Metally, 1967, №4, pp. 85-89.
21. Issledovanie iznosostojkosti splavov hroma. Bakun O.V. i dr. - V kn.: Litye iznosostojkie materialy. K.: 1975, pp. 42-46.

Published

2014-05-23

How to Cite

Осипов, М. (2014). Osipov M.Y. Research of the effect of alloys structural condition on their resistance to abrasive wear under elevated temperatures. Problems of Tribology, 72(2), 51–57. Retrieved from https://tribology.khnu.km.ua/index.php/ProbTrib/article/view/111

Issue

Section

Articles