Chernets M.V., Zhydyk V.B., Chernets Yu.M. The investigation of interval-block interaction parameters influence on sliding bearing durability with small shaft ovality.
Abstract
The presence of low technological ovality (thilobing or tetralobing) of sliding bearing shaft complicates the process of tribocontact task solution of its durability determining using interval-discrete cumulative wear model. Therefore, to reduce the length of calculation the interval-block scheme for this problem solution has been applied. The effect of sampling interval size of the shaft contour and cycles (blocks) of tribocontact interaction at constant conditions on bearing durability has been investigated. Increasing of the sampling interval shaft contour and increasing of the block size can proportionally reduce the calculation (up to 100000 times) with a proportional loss of solution accuracy to 10 %. Found that shaft ovality significantly affect on the bearing durability increasing (21 %).References
1. Chernets M.V., Ljebjedjeva N.M. Ocinka kinetyky znoshuvannja trybosystem kovzannja pry najavnosti ovalnosti konturiv jih elementiv za kumuljacijnoju modellju. Problemy trybologiji, 2005, No 4, p.p. 114-120.
2. Chernets M.V., Andrejkiv O.Je., Ljebjedjeva N.M., Zhydyk V.B. Model ocinky znoshuvannja i dovgovichnosti pidshypnyka kovzannja za maloji nekruglosti. FHMM, 2009, No 2, p.p. 121-129.
3. Chernets M.V., Zhydyk V.B. Uzagalnena kumuljacijna model kinetyky znoshuvannja pidshypnyka kovzannja. Part 1. Linijna i kumuljacijna model. Problemy trybologiji, 2012, No 4, p.p. 11-17.
4. Chernets M.V., Zhydyk V.B. Uzagalnena kumuljacijna model kinetyky znoshuvannja pidshypnyka kovzannja. Part 2. Uzagalnena kumuljacijna model. Problemy trybologiji, 2012, No 4. p.p. 11-17.
5. Chernets M.V. Kontaktna zadacha dlja cylindrychnogo zjednannja z tehnologichnym ogranennjam konturiv detalej. FHMM, 2009, No 6, p.p. 93-99.
2. Chernets M.V., Andrejkiv O.Je., Ljebjedjeva N.M., Zhydyk V.B. Model ocinky znoshuvannja i dovgovichnosti pidshypnyka kovzannja za maloji nekruglosti. FHMM, 2009, No 2, p.p. 121-129.
3. Chernets M.V., Zhydyk V.B. Uzagalnena kumuljacijna model kinetyky znoshuvannja pidshypnyka kovzannja. Part 1. Linijna i kumuljacijna model. Problemy trybologiji, 2012, No 4, p.p. 11-17.
4. Chernets M.V., Zhydyk V.B. Uzagalnena kumuljacijna model kinetyky znoshuvannja pidshypnyka kovzannja. Part 2. Uzagalnena kumuljacijna model. Problemy trybologiji, 2012, No 4. p.p. 11-17.
5. Chernets M.V. Kontaktna zadacha dlja cylindrychnogo zjednannja z tehnologichnym ogranennjam konturiv detalej. FHMM, 2009, No 6, p.p. 93-99.
Downloads
Published
2014-07-10
How to Cite
Чернець, М., Жидик, В., & Чернець, Ю. (2014). Chernets M.V., Zhydyk V.B., Chernets Yu.M. The investigation of interval-block interaction parameters influence on sliding bearing durability with small shaft ovality. Problems of Tribology, 69(3), 23–27. Retrieved from https://tribology.khnu.km.ua/index.php/ProbTrib/article/view/152
Issue
Section
Articles
