Kukhar V.V., Suglobov R.V., Prisyazhnyi A.G. The working of design and projecting methodic for technological lubricants spraying system in automatic lines of die-forging and rolling.
Abstract
The design of ejecting facility for covering of technological lubricants by spraying on lubricating surfaces was proposed for automatic lines of impression die-forging and rolling. The regulation of modes of stream givens of viscid liquids is possible in knot for lubricants spraying for proportional cover guarantee. The experimental researches were executed and depending between modes of work of spraying system and complex of designing and technological factors was finding. Rational design parameters of ejecting spray system were finding and results grounding to the methodic of calculation of new design of knot for spraying of lubricant in metal forming technologies that realized in automatic lines with counting of pressure in air net, quantity of dismiss of axe of absorbing pipe-line from mixing zone, local resistances of pipe-line from condition of changing of length and square of tube cross-section. The methodic of obtain the designing parameters of ejecting spray system for technological lubricant can be improving by method of successive approximations but example for rolling process was shown about given requiring results at first calculation.References
1. Taylan Altan, Mayur Deshpande. Selection of die materials and surface treatments for increasing die life in hot and warm forging. ERC for Net Shape Forming, Paper No 644-FIA Tech Conference, The Ohio State University, April 2011, pp. 1-32.
2. Chun Liu. Modeling of water and lubricant sprays in hot metal working. Dissertation, Presented in Partial Fulfillment of the Requirements for the Degree Doctor of Philosophy, Ph.D., in the Graduate School of The Ohio State University, The Ohio State University, 2007, 282 p.
3. Manas Shirgaokar. Technology to improve competitiveness in warm and hot forging: Increasing die life and material utilization. Dissertation, Presented in Partial Fulfillment of the Requirements for the Degree Doctor of Philosophy, Ph.D., in the Graduate School of The Ohio State University, The Ohio State University, 2008, 296 p.
4. Hot forging die lubrication by the use of zero maintenance spraying systems. Purchase, Tech Article, November, 2012, pp. 149-154.
5. Behrens B.-A., Lueken I., Odening D. Cooling and lubrication of automated forging processes with high-pressure systems. International Journal of Material Forming, 2010, Vol. 3, Issue 1 Sup., pp. 331-334.
6. Sheljaskow S. Tool lubrication systems in warm forging. Journal of Materials Processing Technology, 2001, № 113, pp. 16–21.
7. Pat. WO/2008/071355 Italy, A1, B 21 J 3/00; B 30 B 15/00. Lubricating system and method for a press-forging die. Bassi Stefano, Borgogno Alessandro, Porto Gianluca, Giudici Raoul IT. Petruzziello, Aldo et al. Racheli & C. SPA IT, № EP2007/010678, zajav. 07.12. 2007, opubl. 19.06.2008.
8. Pat. 13855А UA, MPK В 21 J 3/00. Rozpyl’uvach. Diamantopulo K.K., Kaplanov V.I., Diamantopulo O.K. UA, Mariupol’skyi matalurgijnyi instytut. № 94041255, zajav. 31.12.1992, opubl. 25.04.1997, Bul. No. 2.
9. Smyslov V.V. Gidravlika I aerodinammika. Kiev, Vysha shkola, 1979, p. 336.
10. Pat. 11783 UA, MPK 2006 B 21 J 3/00. Rozpyl’uvach. Diamantopulo K.K., Kukhar V.V., Prisyazhnyi A.G. UA, Pryazovskyi derzhavnyi technichnyi universytet. № u200505681, zajav. 13.06.05, opubl. 16.01.06, Bul. No. 1.
2. Chun Liu. Modeling of water and lubricant sprays in hot metal working. Dissertation, Presented in Partial Fulfillment of the Requirements for the Degree Doctor of Philosophy, Ph.D., in the Graduate School of The Ohio State University, The Ohio State University, 2007, 282 p.
3. Manas Shirgaokar. Technology to improve competitiveness in warm and hot forging: Increasing die life and material utilization. Dissertation, Presented in Partial Fulfillment of the Requirements for the Degree Doctor of Philosophy, Ph.D., in the Graduate School of The Ohio State University, The Ohio State University, 2008, 296 p.
4. Hot forging die lubrication by the use of zero maintenance spraying systems. Purchase, Tech Article, November, 2012, pp. 149-154.
5. Behrens B.-A., Lueken I., Odening D. Cooling and lubrication of automated forging processes with high-pressure systems. International Journal of Material Forming, 2010, Vol. 3, Issue 1 Sup., pp. 331-334.
6. Sheljaskow S. Tool lubrication systems in warm forging. Journal of Materials Processing Technology, 2001, № 113, pp. 16–21.
7. Pat. WO/2008/071355 Italy, A1, B 21 J 3/00; B 30 B 15/00. Lubricating system and method for a press-forging die. Bassi Stefano, Borgogno Alessandro, Porto Gianluca, Giudici Raoul IT. Petruzziello, Aldo et al. Racheli & C. SPA IT, № EP2007/010678, zajav. 07.12. 2007, opubl. 19.06.2008.
8. Pat. 13855А UA, MPK В 21 J 3/00. Rozpyl’uvach. Diamantopulo K.K., Kaplanov V.I., Diamantopulo O.K. UA, Mariupol’skyi matalurgijnyi instytut. № 94041255, zajav. 31.12.1992, opubl. 25.04.1997, Bul. No. 2.
9. Smyslov V.V. Gidravlika I aerodinammika. Kiev, Vysha shkola, 1979, p. 336.
10. Pat. 11783 UA, MPK 2006 B 21 J 3/00. Rozpyl’uvach. Diamantopulo K.K., Kukhar V.V., Prisyazhnyi A.G. UA, Pryazovskyi derzhavnyi technichnyi universytet. № u200505681, zajav. 13.06.05, opubl. 16.01.06, Bul. No. 1.
Downloads
Published
2014-07-14
How to Cite
Кухарь, В., Суглобов, Р., & Присяжный, А. (2014). Kukhar V.V., Suglobov R.V., Prisyazhnyi A.G. The working of design and projecting methodic for technological lubricants spraying system in automatic lines of die-forging and rolling. Problems of Tribology, 70(4), 137–143. Retrieved from https://tribology.khnu.km.ua/index.php/ProbTrib/article/view/195
Issue
Section
Articles
