Chernets M.V. To the question about the calculation of limits the changes of the teeth gearing in cylindrical obliquely teeth transmissions of and its influence on pin pressures.

Authors

  • М.В. Чернець

Abstract

The paper presents the results undertaken the using of methodology of calculation the corners that is determined by the limits of the gearing the teeth pairs correction in cylindrical transmissions. Considered the cases of two-one pairs teeth, three-two pairs teeth, four-three pairs teeth gearing. The analysis of influence to gearing the teeth pairs on a size and charac-ter of change the maximal contact pressures was conducted . Key words: cylindrical gearing , limits of gearing changes , two-one pairs teeth, three-two pairs teeth, four-three pairs teeth gearing, maximum contact pressure

References

1. Ocinka dovhovicznosti, znoszuvannja ta kontaktnoi micsnosti zubczastyh peredacz. Pid zah. red. M.V.Chernecja. – Drohobycz: Vymir. 2002. 128 s.
2. Chernec M.V., Kielbinski Ju., Jarema R.Ja. Uzahalnenyj metod ocinky znoszuvannja cylindrycznych evolventnych zubczastych peredacz. FKhMM, №1, 2011. S. 44 – 49.
(Chernets M.V., Kelbinski J., Jarema R.Ja. Generalized method for the evaluation of cylindrical invo-lute gears. Materials Science, №1, 2011. P. 45 – 51.)
3. Chernec M.V., Jarema R.Ja., Czernec Ju.M. Metod ocinky vplyvu koryhuvannja i znoszuvannja zubiv evolventnoi cylindrycznoi peredaczi na dovhovicznist ta micnist. Czast. 1. Dovhovicznist ta znoszuvannja. FKhMM, №3, 2012. S. 30 – 39.
(Chernets M.V., Yarema R.Ya., Chernets Yu.M. A method for the evaluation of the influence of correc-tion and wear of the teeth of a cylindrical gear on its durability and strength. Part 1. Service live and wear. Mate-rials Science, №3, 2012. P. 289 – 300.)
4. Chernec M.V., Jarema R.Ja., Czernec Ju.M. Metod ocinky vplyvu koryhuvannja i znoszuvannja zubiv evolventnoi cylindrycznoi peredaczi na dovhovicznist ta micnist. Czast. 2. Kontaktna micnist. FKhMM, №6, 2012. S. 56 – 59.
(Chernets M.V., Yarema R.Ya., Chernets Yu.M. A method for the evaluation of the influence of correc-tion and wear of the teeth of a cylindrical gear on its durability and strength. Part 2. Contact strength. Materials Science. 2012. №6. S. 752 – 756.)
5. Chernec M.V., Chernec Yu.M. Doslidzhennia umov zaczeplennia zubiv cylindrycznoi evolventnoi peredaczi na kontaktnu micnist, znoszuvannja i dovhovicznist. Czast. 1. Postijni umovy vzaiemodiji u nekoryhovanomu zaczeplenni. Problemy trybologii, №3, 2014. S.84 - 92.
6. Chernec M.V., Chernec Yu.M. Doslidzhennia umov zaczeplennia zubiv cylindrycznoi evolventnoi peredaczi na kontaktnu micnist, znoszuvannja i dovhovicznist. Czast. 3. Zminni umovy vzaiemodiji u nekoryhovanomu zaczeplenni. Problemy trybologii, №4, 2014. S.49 - 53.

Published

2016-12-23

How to Cite

Чернець, М. (2016). Chernets M.V. To the question about the calculation of limits the changes of the teeth gearing in cylindrical obliquely teeth transmissions of and its influence on pin pressures. Problems of Tribology, 82(4), 10. Retrieved from https://tribology.khnu.km.ua/index.php/ProbTrib/article/view/560

Issue

Section

Articles

Most read articles by the same author(s)

1 2 3 > >>