Wear resistance increase of samples tribomating "Steel 45-cast iron SCH20" with geo modifier KGMF-1
DOI:
https://doi.org/10.31891/2079-1372-2019-92-2-55-60Keywords:
tribomating of sample, geo modifier, composite oil, friction torque, wear resistance, acoustic emission, friction area, oil M-10G2KAbstract
Increase of wear resistance of different types of tribomating which are functioning in fluid lubrication is possible due to: choosing more expensive and high quality material of samples that is not always sensible; applying some wear resistant coatings on them; selection and formation of complex composition of oil additives. Due to nanomaterials development there is a possibility of efficient use of functional additives such as geo modifiers in tribology. Due to geo modifier-based oil composites use it’s not necessary to make any structural changes of machines mated parts though their wear resistance is increased. It requires the conducting of some experimental tribological research. It was found that oil media modified by a geo modifier increase the wear resistance of working surfaces of different types of tribomating. The use of geo modifier КGМF-1 (Katerynivka friction geo modifier-1) has been suggested. Samples division into 4 types of mating according to the following characteristic features: mobility, material hardness and friction area has been suggested for more accurate picture of wear resistance changes of samples tribomating which are functioning in base and modified oil. Lower friction torque of different samples couplings in modified oil by geo modifier КGМF-1 in comparison with base oil M-10G2K was recorded while using Friction machine 2070 SMT-1 with add-on module "ring-ring". The samples wear rate in modified oil by geo modifier КGМF-1 in comparison with base oil M-10G2K was studied by method of acoustic signal amplitude measurements directly from the friction zone by a commercially produced instrument of Brüel & Kjear company. Moreover, it was recorded that the maximum wear rate of samples in their functioning in modified oil M-10G2K + КGМF-1 was 2...3 times lower, and friction torque change law is similar to the wear rate change depending on the time of testing
References
2. V. Aulin, V. Slon, S. Lysenko, The Character of Change of Tribo-Technical Descriptions of Interfaces of Diesels During Their Work in the Different Modes, The Problems of Tribology. Khmelnytskyi, no. 3, pр. 89-96, 2013.
3. V. Aulin, A. Hrinkiv, A. Dykha, M. Chernovol, O. Lyashuk, S. Lysenko, Substantiation of Diagnostic Parameters for Determining the Technical Condition of Transmission Assemblies in Trucks, Eastern European Journal of Enterprise Technologies, vol. 2, no. 1(92), pp. 4-13, 2018.
4. А.P. Pavlov, N.G. Petrov, Comparative Analysis of Motor Oil Additives Characteristics Sold on Rus-sian Market, Automobile. Road. Infrastructure, vol. 2, no. 12, pp. 5-12, 2017.
5. М.N. Svyryd, А.P. Kudryn, L.B. Pryimak, Use of ХАDО-additives in Tribomagnetic Reconditioning, Bulletin of Khmelnytskyi National University, vol. 6, pp. 122-125, 2011.
6. D.А. Gomon, А.М. Dudka, І.І. Nachovnyi, Comparative Study of Motor Oil Anti-Wear Additives Per-formance. VIII International scientific-technical conference «Chemistry and Modern Technologies», vol. V, Dni-pro, 26-28 April, 2017, pp. 125, 2017.
7. G.M. Ashmarin, V.V. Aulin, M. Yu. Golubev, S.D. Zvonkov, Grain Boundary Internal Friction of Un-alloyed Copper Subjected to Continuous Laser Radiation, Physics and Chemistry of Materials Treatment, vol. 20, no. 5, pp. 476-478, 1986.
8. M.I. Chernovol, E.K. Solovykh, Prediction of Thickness of Solid-Lubricant Film Formed at Friction of Metal-Polymer Composite Coating, Journal of Friction and Wear, vol. 18, no. 2, pp. 40-45, 1997.
9. A. Dunayev, S. Sharifullin, Modernisation of Threadbare of Technique with the Use of Tribo-Preparations, Kazan: Edition of the Kazan University, 2013.
10. D. Vasilkov, I. Pustovoy, The Analysis of the Layer Formed by the Mineral Modifier of Surface of Friction, Мoscow: Trudy GOSNIITY, vol. 107, iss. 2, pp. 11-13.
11. S. Baskar, G. Sriram, S. Arumugam, Experimental Analysis on Tribological Behaviour of Nano Based Bio-Lubricants Using Four Ball Tribometer, Tribology in Industry, vol. 37, no. 4, pp. 449-454, 2015.
12. V. Aulin, A. Hrynkiv, S. Lysenko, I. Rohovskii, M. Chernovol, O. Lyashuk, T. Zamota, Studying Truck Transmission Oils Using the Method of Thermal-Oxidative Stability during Vehicle Operation, Eastern-European Journal of Enterprise Technologies, vol. 1, no. 6(97), pp. 6-12, 2019.
13. B. Basu, M. Kalin, Tribology of Ceramics and Composites: Materials Science Perspective, New York: Wiley, 2011.
14. V. Aulin, T.N. Zamota, S. Lysenko, Increase of Machine Parts Performance Wear Resistance by Their Tribological Reconditioning and Control of Wear-In Processes, MOTROL. Commission of Motorization and En-ergetics in Agriculture, vol. 18, no. 2, pp. 89-96, 2016.
15. V. Aulin, W. Arifa, S. Lysenko, A. Kuzyk, Improving of the Wear Resistance of Working Parts Agri-cultural Machinery by the Implementation of the Effect of Self-Sharpening, International Journal of Engineering and Technology, vol. 5, no. 4, pp. 126-130.
16. C. Anderberg, Z. Dimkovski, B.-G. Rosén, T.R. Thomas, Low Friction and Emission Cylinder Liner Surfaces and the Influence of Surface Topography and Scale, Tribology International, pp. 224-229, 2019.
17. T. Kuwahara, P.A. Romero, S. Makowski, V. Weihnacht, G. Moras, M. Moseler, Mechano-Chemical Decomposition of Organic Modifiers With Multiple Reactive Centres Induces Superlubricity of Ta-C, Nature Communications, vol. 10, no. 1, 151, 2019.
18. J. Yuansheng, L. Shenghua, Superlubricity of in Situ Generated Protective Layer on Worn Metal Sur-faces in Presence of Mg6Si4O10(OH)8, in A. Erdemir, J.M. Martin (Ed.): Superlubricity. Elsevier, pp. 445-469, 2007.
19. M. Ebrahimi, M.H. Shaeri, C. Gode, H. Armoon, M. Shamsborhan, The Synergistic Effect of Dilute Alloying and Nanostructuring of Copper on the Improvement of Mechanical and Tribological Response, Com-posites Part B: Engineering, vol. 164, pp. 508-516, 2019.
20. A. Dounaev, Friction Surfaces Modification Using Tribo-Compounds, World Applied Sciences Jour-nal, vol. 31, no. 2, 272-276, 2014.
21. A. Dykha, V. Aulin, O. Makovkin, S. Posonskiy, Determining the Characteristics of Viscous Friction in the Sliding Supports Using the Method of Pendulum, EasternEuropean Journal of Enterprise Technologies, vol. 3, no. 7(87), pp. 4-10, 2017.
22. D. Lutsak, P. Prysyazhnyuk, M. Burda, V. Aulin, Development of a Method and an Apparatus for Tri-botechnical Tests of Materials Under Loose Abrasive Friction, EasternEuropean Journal of Enterprise Technolo-gies, vol. 5, no. 7(83), pp. 19-26, 2016.
23. V. Aulin, V. Slon, S. Lysenko, D. Holub. Pat. 81598 Ukraine, The Work Piece Lubricating Composi-tion, Declarant and Patent holders is the Kirovohrad National Technical University, №u201213907, declared 06.12.2012, published 10.07.2013, no. 13, 2013.
24. Z. Geng, D. Puhan, T. Reddyhoff, Using Acoustic Emission to Characterize Friction and Wear in Dry Sliding Steel Contacts. Tribology International, vol. 134, pp. 394-407, 2019.